NET SAFETY MONITORING, INC
BANSHEE 343 ULTRASONIC GAS LEAK DETECTOR
The Banshee343 is an advanced gas leak detection system utilizing four ultra-sensitive acoustic sensors which constantly monitor wide areas for ultrasound generated from the release of pressurized gas. Ideally suited for monitoring well ventilated outdoor environments, the Banshee343 has been engineered to withstand even the most extreme conditions while including features designed to optimize performance and reduce maintenance.
Ultrasonic (acoustic) gas leak detection technology has several advantages over conventional gas sensor technologies: it does not have to wait until a gas concentration has accumulated to potentially dangerous concentrations, it does not require a gas cloud to eventually make physical contact with a sensor, and the response is instantaneous for all gas types.
- Widest Area of Coverage, 40 Meter Radius Through Four independent Sensors
- Instantaneous Response To All Types of Gas Leaks (LEL or ppm)
- Wide Temperature Range: -55°C — +85°C
- SonicCAL System — Automated Self Test and Sensor Cleanse – Failsafe & Maintenance Free
- Analog, Relay, and RS485 Digital Modbus
- Certified Worldwide for Hazardous Locations
- Detection range: 25kHz to 100 kHz — Widest Dynamic Range Available, 50db — 140dB
- Innovative Mapping Tool Helps Operators Achieve Optimum Performance At Site Location
- Programmable Time Delays to Allow for Pressure Venting, Etc.
The Banshee343 detects deadly gas leaks at the speed of sound without being affected by inclement weather, wind direction, leak direction or any potential gas dilution. When utilized together with Net Safety point gas detection and our optical flame detection, a complete and comprehensive safety system is ensured.
ABOUT ULTRASONIC GAS LEAK DETECTION TECHNOLOGY
Ultrasonic (acoustic) gas leak detection technology functions through the constant monitoring of wide areas by advanced acoustic sensors specially tuned to process ultrasound emitted from pressurized gas leaks. This detection technology has several advantages: it does not have to wait until a gas concentration has accumulated to potentially dangerous concentrations, it does not require a gas cloud to eventually make physical contact with a sensor, and the response is instantaneous for all gas types.
Simply put, the ultrasonic leak detector only triggers an alarm when inaudible, ultrasound is detected (between 25 – 100 kHz) — which is only produced with the release of highly pressurized gas. This makes for extremely reliable and efficient performance by the detection system as there is no poisoning of sensors, it never requires field calibration, and all background noises are accurately filtered.
The Banshee343 detects deadly gas leaks at the speed of sound without being affected by inclement weather, wind direction, leak direction or any potential gas dilution. When utilized together with Net Safety point gas detection and our optical flame detection, a complete and comprehensive safety system is ensured
ULTRASONIC DETECTION COVERAGE
In order to achieve optimum performance a site mapping survey is necessary to check background noise levels, ensure alarm levels are set above the normal background conditions, programming any necessary time delays to allow for pressure venting, and to ensure all potential leak areas have coverage by a detector footprint. Net Safety technicians are available during installation and commissioning as well as providing full training with our NSM-MT-01 mapping tool.
PHOENIX TRIPLE IR FLAME DETECTOR
The Phoenix will only alarm when input conditions from three distinct IR wavelengths found in fires are satisfied. The Phoenix also incorporates our unique Automatic Digital Zoom (ADZ) technology which provides accurate detection of small and massive flames in the most difficult working situations where other detectors fail. Three precisely tuned IR sensors, ADZ technology, user selectable sensitivity, and time delay settings greatly extend the Phoenix Triple IR detection range, providing unparalleled false alarm immunity and detection performance.
The Phoenix Triple IR is the ONLY flame detector on the market that does not have an external reflector or light source. Experience has shown that external reflectors and light sources often become obscured by industrial dirt and corrosion which causes unwanted fault alarms that requires difficult and costly maintenance to correct. The Phoenix Triple IR flame detector completely eliminates these issues in applications where salt, dust, petroleum vapor, heavy rain, snow or blowing sand are present. Our patented Automatic Visual Integrity testing technology continuously checks optical surfaces for contaminants while at the same time verifying functionality of the sensors and circuitry
Millennium Smoke and Oil Mist Detector
The Millennium Smoke and Oil Mist Detector’s advanced sensor technology utilizes a powerful, single-beam IR lamp with no mirrors to ever be contaminated. Known contamination and reliability issues with “open path” mist detectors are eliminated as our point system design protects the lens from contaminants and does not operate with a reflector. Sensor performance is also not effected by high volume air velocity which allows for accurate reliable monitoring in any duct application. Field adjustable zero level of obscuration as well as multiple sensitivity settings allows for fine tuning within specific application conditions to optimize performance and eliminate false alarms.
MILLENNIUM II MULTI AND SINGLE CHANNEL GAS DETECTION
With it’s innovative multi-channel controller technology and state-of-the-art SMART (Self Monitoring Analysis and Reporting Technology) sensors, the Millennium II Series of gas detectors is exceptionally versatile. With the optional dual channel option you can cover more area with a single transmitter and mix and match all sensor types.
Sensors can be easily exchanged, with Infrared, Solid State MOS, Electrochemical and Catalytic Bead sensors available and compatible with both the Millennium II and Millennium II BASIC transmitters. The Millennium II transmitter automatically recognizes any connected pre-calibrated sensor and maintains an uninterrupted digital signal between them, providing leading response times including the fastest response time in the market today for H2S Hydrogen Sulfide gas detection.
IRM90 Motion Detector
EXPLOSION PROOF INFRARED (IR) MOTION DETECTOR
The IRM90-R is a passive infrared (PIR) motion detector is designed to provide maximum safety and security from occupational hazards and ensure workplace safety – even in the most hazardous and remote locations.
The detector monitors infrared radiation in the 8 to 15 micrometer range and looks for changes in this radiation such as an intruder walking through its 65 degree cone of vision, in order to relay an alarm.
The IRM90-R comes with a swivel mount to make mounting and angle adjustments fast and easy. The explosion-proof housing is factory sealed to simplify installation. Normally closed relay contacts allow for connection to alarm circuitry, annunciation panels or other devices. The electronic circuitry does not require any adjustments by the user coverage by one camera.
FEATURES
- 3/4″, NPT conduit fitting for easy installation
- Factory sealed enclosure eliminates the need for conduit seals in the field
- Normally closed, “fail-safe” relay contacts for connection to alarm circuitry or other devices. Contacts become open when motion is detected or power is lost to the detector
- One meter of 16 AWG cable is connected to the detector
- No-tool swivel mount provided to adjust angle and simplify installation
ECO-SENSE 2 WIRE LOOP-POWERED H2S GAS DETECTOR
The Net Safety Monitoring ECO-SENSE detector is a truly state-of-the-art H2S gas sensor/transmitter package designed specifically for 2 wire, loop-powered installations. An economic and ecological choice, this extremely low power detector functions in a 4-20mA “sink” mode at less than .75 watts with 10-30 Vdc with a full LED display.
Operator interface is via a menu driven magnetic keypad allowing full access without opening the enclosure. There are no potentiometers and all adjustments are performed through the keypad. Requires only a simple calibration magnetic (included) for non-intrusive calibration, no other special electronic devices are needed.
MILLENNIUM II TOXIC GAS DETECTOR
Net Safety’s next generation detector, the Millennium II BASIC is a robust, reliable, and low-cost safety solution delivering highly accurate detection and protection. Our state-of-the-art “SMART” (Self Monitoring Analysis and Reporting Technology) sensors provide a cost-effective detector solution that includes all the features you demand with complete ease-of-use and operation.
A full range of Combustible (Catalytic Bead & Infrared) and Toxic (Solid State & Electrochemical) sensors are available, all are completely interchangeable with the Millennium II and Millennium II BASIC transmitters.
SOLAR SHIELD; SOLAR POWERED DETECTION SYSTEM
Net Safety’s autonomous solar power system, the Solar Shield, is easy to install and simple to use. Its clever modular design is conveniently pre-wired and employs quick-connectors and plugable cables between the controller, solar panels and batteries – making installation virtually effortless!
With the Solar Shield’s prepackaged design and easy to configure outputs, wiring is minimized – saving you time and money when installing or performing maintenance. The scrolling display and status LEDs provide helpful information for field setup, operation and maintenance!
Select the hazard protection you need (Fire detectors, Toxic Gas or Combustible Gas sensors), and provide our sales representative with your specific installation location and load requirements. We’ll use that information to deliver a solar power system, sized to meet your unique site requirements
COMPLETE SYSTEM SOLUTIONS
Net Safety System Solutions is a product-independent, complete safety system provider. We offer fit-for-purpose technology solutions for F&G (Fire & Gas) and ESD (Emergency Shut Down) Systems with up to SIL 3 certification. What sets us apart is the ability to provide our customers with the total package – a specialized engineering solution within a wide range of specifications. We design your entire system utilizing the most efficient and cost-effective combination of products for your specific application – and we then fully support the entire system, from the HMI all the way down to the field devices.
When you partner with Net Safety Monitoring System Solutions you have a single source for the design, manufacture and support – for the life of your system.
With our one-stop-shop solution you’ll have the assurance that all aspects of your system design comes from a single source with full product support. Fire and gas detection has been our business for almost 20 years, our team of safety experts will work with you every step of the way to provide you with the optimum system solution to best meet your application requirements. Designed with a modular approach, our solutions also offer complete expansibility – whether connecting to legacy systems or the systems of tomorrow. We’re ready to help, let’s talk.
PLANTSAFE 8000 | PLANTSAFE 7000 | PLANTSAFE 6000
CORE ACTIVITIES OF NET SAFETY SYSTEM SOLUTIONS
- Project Management of Safety Systems
- Project Engineering
- Hardware Design/Panel Design
- Documentation
- Panel Fabrication
- Software Design and Development
- Factory Acceptance Tests
- Site Acceptance Tests
- Commissioning and Start-Up Activities
- Post Sales Support Services
PLANTSAFE 8000
The PLANTSAFE 8000 is a PLC based solution approved for SIL 2 applications as per IEC 61508/61511 by TÜV for safety system applications. The system can be configured with dual or simplex CPU with simplex I/O. The system’s rugged open control platform incorporates Modbus TCP with built-in Fault Tolerant Ethernet (FTE) for redundant communications, providing you simple but secure connections to a wide range of standard software and hardware packages. This unique open approach allows users flexible migration paths. Connect to yesterday’s legacy control systems, interface with the most up-to-date instruments and software packages and look forward to the products that aren’t even developed yet – knowing that the PlantSafe 8000 will connect to them.
Features of this system are:
- SIL 2 Certified
- Certified to Class I Div II
- Conforms to NFPA 72
- Conforms to NFPA 85
- IEC 61131 Programming
- UL/CSA Approvals
PLANTSAFE 7000
The PLANTSAFE 7000 is a SIL 3 PLC based F&G system utilizing single rack and multiple rack system platforms. All systems are TÜV certified to SIL 3 according to IEC 61508 and meet all the requirements of IEC 61511 for when used as part of a F&G system. The system is inherently safe, achieving SIL 3 without the need for voting or redundant modules, and without any “degraded modes” or “time restrictions” for SIL 3 operation. It can also be configured as fully fault tolerant, providing maximum availability with SIL 3 safety.
Features of this system are:
- TÜV Certified for SIL 3 applications
- Simplex or Fault Tolerant Configurations (scaleable)
- TÜV Certified to NFPA 72
- TÜV Certified to NFPA 85
- TÜV Certified SIL 3 communications via safe ethernet
- Tight, seamless integration with any BPCS on the market
- IEC 61131-3 Programming
- TÜV Certified Function Blocks
- Certified to Class I Division II
- CSA, FM, FMC, UL, ULC Approvals
PLANTSAFE 6000
The PLANTSAFE 6000 is a PLC based system utilizing a range of intelligent safety PLC’s and remote I/O blocks (safety nodes). The PLC’s and remote I/O blocks are connected via high speed safe ethernet – using standard Ethernet networking hardware and TÜV certified for SIL 3 integrity between each. The safe ethernet network can be implemented in a high availability “ring” architecture allowing you to distribute your safety processing nodes throughout the plant – where ever you need them, providing significant saving in home run cabling. The PlantSafe 6000 is built on proven inherently safe technology SIL 3 certified “out of the box”, with no user configuration engineering required. PLC nodes start at just eight I/O with a comprehensive variety of remote I/O blocks, the small size and low cost make it an ideal fit for distributed applications with low I/O counts – but flexible enough to build large networks of safety protection.
Features of this system are:
- TÜV Certified for SIL 3 applications
- Connected by TÜV certified safe ethernet
- Low cost, scaleable architectures
- Easy DCS integration using same safe ethernet network via OPC DA, Modbus TCP, Ethernet IP or Serial using Modbus or Profibus on RS-485 networks
- IEC 61131-3 Programming
- TÜV Certified Function Blocks
- Certified to Class I Division II
- FM, FMC, UL, ULC Approvals
